2010-2013 Chevrolet Camaro SS 6.2L 63 Series Aircharger Kit

2010-2013 Chevrolet Camaro SS 6.2L 63 Series Aircharger Kit

• Part 63-3074 Product Specifications
• Product Style: 63 Series Aircharger Kits
• Estimated Horsepower Gain: 18.62 HP @ 5161 RPM
• Replacement Filter: RF-1042
• Street Legal In All US States: No
• TUV Approved (Europe): No
• Clamp Style: Regular
• Intake Pipe Color / Finish: Black
• Weight: 11.4 lb (5.2 kg)
• Product Box Length: 22.25 in (565 mm)
• Product Box Width: 14.25 in (362 mm)
• Product Box Height: 12.5 in (318 mm)

The World's Best Flowing, Best Filtering, High Performance Air Intake Systems

• Guaranteed to Provide more HP and Increased Acceleration
• Engineered to Specific Vehicle Design
• Easy to Install, Usually in 90 minutes or less!
• Lasts up to 100,000 Miles Before Service is Required (depending on driving conditions)
• Million Mile Limited Warranty
• Air Filter is Washable and Reusable
• Replaces OEM Filter and Air Box
• Works with Original Equipment Manufacturer Computer Systems
• Designed to use Factory Holes & Mounting Points Whenever Possible
• Street legal in most states (not street legal in CA – Check part number or vehicle listing for specific CARB status)

Our 63 Series Air Intake Kits (AirCharger®) are a sister product to our 57 Series FIPK's.  These intakes are built for many different vehicles and represent a dramatic improvement over a K&N O/E replacement filter alone; they use only non-metallic rotationally molded tubes that can reduce intake air temperature and decrease intake sound over a metal tube.  Restriction can exist BETWEEN an air filter and the engine reducing the benefit of a K&N Air Filter.  The weakest link in the airflow “chain” robs a vehicle of its natural horsepower.  Often that weak point is the factory air path leading to the Engine.  K&N Air Intake Kits virtually eliminate air path restriction by replacing the air filter and the entire air path to the engine.  The aerodynamically engineered tube drives a massive amount of air into an engine, which translates into POWER.

Our 63 Series kits are truly state-of-the-art. We start with the largest conical shaped High-Flow air filter we can fit into the engine compartment while using factory holes and mounting points. This extra filter size provides even more airflow at lower restriction than a standard K&N O/E replacement filter that is limited to the size of the factory air box. The oversize air filter also captures and holds more dirt increasing the service life before a cleaning is required (up to 100,000 miles). The filter is isolated from high engine temperature by a heat shield designed to lower the temperature of the air entering the engine, which increases horsepower. Next we attach the filter to a rotationally molded tube made from interlaced High Density Polyethylene. This process allows us to precisely shape the tube to reduce turbulence and accelerate airflow into the engine. This is why some of our tubes have unique shapes or indentations that are specifically engineered for each application. Finally the tube is connected to the engine with adapters made from high strength materials such as silicon and reinforced nylon and ensures long life. Put all this together and you have the best high-flow intake system available today.

This intake system is not legal for street use in the following states:

Arizona, California, Connecticut, District of Columbia, Maine, Maryland, Massachusetts, New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington

This intake system is legal for street use in most states. However, it is not legal for street use in California and the above states that have adopted California Emissions Standards under Section 177 of the Federal Clean Air Act of 1970. Intake systems are subject to governmental regulation in California and certain other states adopting the emission standards of the California Air Resources Board. In order for an intake system to be legal on a specific vehicle in California and the other adopting states, the part number must receive a CARB Executive Order (EO) number. This number makes the part legal for use only on specific years, makes and models of vehicles. A decal with CARB EO number for these parts must be displayed in the engine bay to satisfy smog inspection requirements.

All K&N 57 series intakes for North American vehicles have received CARB EO numbers and are street legal in all 50 states.

ABOUT K&N

For over 50 years, K&N has been an industry-leader in automotive filtration and technology—offering products to increase performance, protection, and longevity in thousands of vehicle applications for consumers worldwide.

HISTORY

In the early 1960s, two motorcycle racers, Ken Johnson and Norm McDonald (K&N), developed a ground-breaking new idea for an air filter—one that could perform under the demands of dusty, dirty off-road environments. After experimenting with numerous types of filter media, they discovered that an oiled cotton design allowed the filter to not only capture contaminants very efficiently, but also allowed it to be washed and reused, and the original K&N High-Flow Air Filter was born. Five decades later, K&N is still innovating industry-leading filtration technology, and offers outstanding protection for everything from top-fuel dragsters to commuter vehicles across the globe.


PRODUCTS

In addition to performance air filters, K&N® now manufactures a variety of other protection and performance products, including air intake systems, oil filters, fuel filters, cabin air filters, and home air filters, with a reputation for exceptional quality and customer service that millions of customers trust.


K&N has maintained active involvement in racing and motorsports throughout its history, and has sponsored championship-winning teams in most subdisciplines of motorsport. A long and storied racing heritage continues to contribute to the development of products for all types of vehicles and engines.